The MIC2954 is an efficient voltage regulator with very low dropout voltage (typically 40 mV at light loads and 375 mV at 250 mA), and low quiescent current (120 µA typical). The quiescent current of the MIC2954 increases only slightly in dropout, thus prolonging battery life. Key MIC2954 features include protection against reversed battery, fold-back current limiting, and automotive load dump protection (60V positive transient).
The LT3014B is a high voltage, micropower low dropoutlinear regulator. The device is capable of supplying 20mA of output current with a dropout voltage of 350mV. Designed for use in battery-powered or high voltage systems, the low quiescent current (7µA operating) makes the LT3014B an ideal choice. Quiescent current is also well controlled in dropout.
The TPS717 family of low-dropout (LDO), low-power linear regulators offers very high power-supply rejection (PSRR) while maintaining very low 45-μA ground current in an ultra-small, five-pin SOT package. The family uses an advanced BiCMOS process and a PMOS pass device to achieve fast start-up, very low noise, excellent transient response, and excellent PSRR performance.
The LM285/LM385 series are micropower two−terminal bandgap voltage regulator diodes. Designed to operate over a wide current range of 10 A to 20 mA, these devices feature exceptionally low dynamic impedance, low noise and stable operation over time and temperature. Tight voltage tolerances are achieved by on−chip trimming
The LMV93x-N family (LMV931-N single, LMV932-N dual and LMV934-N quad) are low-voltage, lowpower operational amplifiers. The LMV93x-N family operates from 1.8-V to 5.5-V supply voltages and have rail-to-rail input and output. The input commonmode voltage extends 200 mV beyond the supplies which enables user enhanced functionality beyond the supply voltage range
This new SIDACtor series thyristors are targeted for the tertiary or line driver side protection position for VDSL2+, ADSL2 applications and general I/O protection functions. This new low capacitance over voltage protection does not require a bias voltage and is sufficiently robust for the chipside position behind the coupling transformer.
Melexis MLX92352 3-Axis Programmable Hall Effect Latch/Switches offer sensitivity to magnetic fields applied to the package's X, Y, and Z axes. Various axes combinations of ZX, ZY, XY, XX, YY, or ZZ on the device's open-drain outputs are possible. The MLX92352 provides ultimate configurability with a 90° phase shift for a pitch-independent magnetic design.
The MAX2039 high-linearity passive upconverter or downconverter mixer is designed to provide 7.3dB NF and a 7.1dB conversion loss for an RF frequency range of 1700MHz to 2200MHz to support UMTS/WCDMA, DCS, and PCS base-station transmitter or receiver applications.
InDART is a powerful and low-cost online debugging (ICD) and online programming (ICP) tool, which was developed for ST7 in cooperation with Softec Microsystems. InDART provides a parallel or USB connection to the host PC according to the model, and a 10 pin ICC connection to the evaluation or application board.
The CDCVF2509 is a high-performance, low-skew, low-jitter, phase-lock loop (PLL) clock driver. It uses a PLL to precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal. It is specifically designed for use with synchronous DRAMs. The CDCVF2509 operates at a 3.3-V VCC. It also provides integrated series-damping resistors that make it ideal for driving point-to-point loads
The DG9636 is a CMOS, dual SPDT analog switch designed to operate from 2.7V to 12V, single supply. All control logic inputs have a guaranteed 1.65 V logic HIGH threshold when operation from a 12 V power supply. This makes the DG9636 ideally suited to interface directly with low voltage micro-processor control signals
FDA803S and FDA903S are the latest single channel fully differential 10W Class D audio power amplifiers in the Italian French semiconductor FDA (pure digital amplifier) series. Target applications include emergency road rescue, remote information processing and any vehicle system that requires audio channel to generate voice, music or prompt messages with maximum 10W standard output power.
The STMICRO EVALST-3PHISOSD evaluation board implements a complete three-phase current meter with a low-cost shunt current sensor. The solution is based on the ISOSD61 device, a single-channel, electrically isolated second-order sigma-delta modulator that measures the current of each phase through a shunt current sensor.
The EL1528 is a dual channel differential amplifier designed for driving full rate ADSL signals at very low power dissipation. The high drive capability of 450mA makes this driver ideal for both CAP and DMT designs. It contains two pairs of wideband, high-voltage, current mode feedback amplifiers optimized for low power consumption in DSL systems
The X9429 integrates a single digitally controlled potentiometer (XDCP) on a monolithic CMOS integrated circuit. The digital control potentiometer is realized by series array of 63 resistance elements. Between each element are tap points connected to the wiper terminal by a switch. The user controls the position of the wiper on the array through the 2-wire bus interface
The AMC1304 is a precision, delta-sigma (ΔΣ) modulator with the output separated from the input circuitry by a capacitive double isolation barrier that is highly resistant to magnetic interference. This barrier is certified to provide reinforced isolation of up to 7000 VPEAK according to the DIN VDE V 0884-11, UL1577 and CSA standards. Used in conjunction with isolated power supplies, the device prevents noise currents on a high common-mode voltage line from entering the local system ground and interfering with or damaging low voltage circuitry.
The MPM38222 is a dual-channel DC/DC module. The module includes a monolithic, step-down, switch-mode converter with built-in, internal power MOSFETs and inductors. The MPM38222 is designed to simplify power system design and provide ease of use.
Both the MP6540 and MP6540A are 3-phase brushless DC motor drivers that integrate three half-bridges and are composed of six n-channel power MOSFETs, driver circuits, gate drive power supplies and current sampling amplifiers.