The Si9712 combines low on-resistance, slow ramp time, and the overall optimal performance of the smart switch in an integrated PC card interface switch. Si9712 is available in two standards and lead-free (Pb) The bag.
The LTM2882 is a complete galvanically isolated dual RS232 µModule (micromodule)transceiver. No external components are required. A single 3.3V or 5V supply powers both sides of the interface through an integrated, isolated DC/DC converter. A logic supply pin allows easy interfacing with different logic levels from 1.62V to 5.5V, independent of the main supply.
The LT5516 is an 800MHz to 1.5GHz direct conversion quadrature demodulator optimized for high linearity receiver applications. It is suitable for communications receivers where an RF or IF signal is directly converted into I and Q baseband signals with bandwidth up to 260MHz. The LT5516 incorporates balanced I and Q mixers, LO buffer amplifiers and a precision, high frequency quadrature generator
The IDT6116SA/LA is a 16,384-bit high-speed static RAM organized as 2K x 8. It is fabricated using IDT's high-performance, high-reliability CMOS technology.
The TAS3208 is a highly integrated audio system-on-chip (SOC) that includes a fully programmable 48-bit digital audio processor, 10:1 stereo analog input MUX, stereo ADC, six Dacs, and other analog features.
The LTC4311 is a dual I2C active pull-up designed to enhance data transmission speed and reliability for bus loading conditions well beyond the 400pF I2C specifi cation limit. The LTC4311 operates at supply voltages from 1.6V to 5.5V and is also compatible with SMBus.
The 'LVT16244B devices are 16-bit buffers and line drivers designed for low-voltage (3.3-V) VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices can be used as four 4-bit buffers, two 8-bit buffers, or one 16-bit buffer. These devices provide true outputs and symmetrical active-low output-enable (OE) inputs.
The RT9715 is a low-cost, low-voltage, single N-MOSFET high-side power switch IC suitable for USB applications. The RT9715 is the ideal solution for USB power and can support flexible applications as it comes in a variety of packages such as the SOT-23-5, SOP-8, MSOP-8 and WDFN 8L 3x3.
The MIC2178 is a 200 kHz synchronous step-down (step-down) switching regulator designed for high-efficiency, battery-powered applications. In a 20-pin wide power SOIC package, the operating temperature range is -40°C to +85°C.
NCP1597B is a fixed 1 MHz, high output current, synchronous PWM converter that integrates a low resistance, high side p-channel MOSFET and a low side n-channel MOSFET.NCP1597B uses internal compensated current mode control to provide good transient response, ease of implementation and excellent loop stability. It can adjust input voltage from 4.0V to 5.5V to output power down to 0.8V, and can provide power up to 2.
The MAX8815A DC-DC step-up converter is a high-efficiency, low quiescent current, synchronous step-up converter with True Shutdown™ and inrush-current limiting. The MAX8815A generates any output voltage from 3.3V to 5V from a 2-cell NiMH/NiCd or a single-cell Li+/Li polymer battery
The LTC1775 is a synchronous step-down switching regulator controller that drives external N-channel power MOSFETs using few external components. Current mode control with MOSFET VDS sensing eliminates the need for a sense resistor and improves efficiency. Largely similar to the LTC1625, the LTC1775 has twice the maximum sense voltage for high current applications. The frequency of a nominal 150kHz internal oscillator can be synchronized to an external clock over a 1.5:1 frequency range.
The MC34163 series are monolithic power switching regulators that contain the primary functions required for dc−to−dc converters. This series is specifically designed to be incorporated in step−up, step−down, and voltage−inverting applications with a minimum number of external components.
LM2665 cmos charge pump voltage converter acts as a voltage doubler with input voltage in the range of 2.5v to 5.5v. Operating current of only 650 μs (over 90% efficiency for most loads) and typical shutdown current of 1μA provide ideal performance for battery powered systems.
The FMS6418A provides comprehensive filtering for set-top box or DVD applications. The filter provides a 2Vpp signal to the AC coupled terminal load. The low-pass filter is powered by 3.3V and has an output of 5.0V. The FMS6418A is available in 16-pin SOIC and 14-pin TSSOP packages.
HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational amplifiers. Each amplifier in the HA-4741 has operating specifications that equal or exceed those of the 741-type amplifier in all categories of performance
The ISL6551 is a zero voltage switching (ZVS) full-bridge PWM controller designed for isolated power systems. This part implements a unique control algorithm for fixed-frequency ZVS current mode control, yielding high efficiency with low EMI. The two lower drivers are PWM controlled on the trailing edge and employ resonant delay while the two upper drivers are driven at a fixed 50% duty cycle.
The FAN7930C is an active power factor correction (PFC) controller for boost PFC applications that operate in critical conduction mode (CRM). It uses a voltage−mode PWM that compares an internal ramp signal with the error amplifier output to generate a MOSFET turn−off signal. Because the voltage−mode CRM PFC controller does not need rectified AC line voltage information, it saves the power loss of an input voltage−sensing network necessary for a current−mode CRM PFC controller
