TI TPA32xx Analog Input Grounding for Single Ended Inputs - Applicazioni | Heisener Electronics
Contattaci
SalesDept@heisener.com 86-755-83210559-827
Language Translation

* Please refer to the English Version as our Official Version.

TI TPA32xx Analog Input Grounding for Single Ended Inputs

Postare su novembre 7, 2018

Single Ended to Differential Input Stage

Figure 1 shows the basic setup for a Single-Ended (SE) to Differential (Diff) input stage used with the TPA32xx amplifier. In this use case, the amplifier is configured for BTL output and requires “Input_A” and “Input_B” to be driven differentially. A pair of inverting Op-amps is used where the Op-amp gain is set to –1. By cascading the operational-amplifiers as shown, the analog signal from the RCA jack labeled “SE Input” appears on both “Input_A” and “Input_B” of the TPA32xx amplifier out of phase with each other.

These operational-amplifiers also run from a single 12 V supply rail to reduce cost. In order to pass analog signals that swing below ground, the operational-amplifiers are biased to the mid rail (6 V) using a resistor divider and filter. Then DC blocking capacitors are used to isolate the Op-amp bias voltage from a ground referenced analog input.

This cost effective SE to Diff converter works quite well; however, since this design is not using a truly differential operational-amplifier stage, there will always be some imbalance between “Input_A” and “Input_B” with this configuration and less than ideal common mode (CM) rejection.

Figure 1. Cost Effective SE to Diff Input Stage

Input Stage with Ground Plane

Now suppose that all of the ground points for the input stage are tied to the ground plane at the most convenient locations, as typically done in PCB layout (Figure 2).

At high output power, the ground plane used for the TPA32xx amplifier will start to see heavy current flow and switching noise. This is generally worse at lower audio frequencies where the sustained amplitude of the audio signal peaks is longer when compared to higher frequency signals. This can cause lots of noise on the ground plane.

Figure 2. SE to Diff Input Stage Ground Plane Noise

Due to the heavy current flow into the ground plane as represented by the arrow “Ipower” noise voltages Vn1, Vn2, and Vn3 develop across the ground plane. Therefore, the ground nodes for the input stage G2, G3, and G4 will all be at different potentials relative to the TPA32xx amplifier analog ground reference G1.

Since our Op-amp input stage is not truly differential with poor CM rejection, signal imbalance is inevitable. It is likely that a differential noise voltage due to Vn1, Vn2, and Vn3 develop between “Input_A” and “Input_B” and is amplified by the TPA32xx amplifier.

This results in degraded low frequency audio performance.

Input Stage with Star Ground

To fix this issue of different THD+N results between stereo channels at 100 Hz is simply ground plane noise, G2, G3, and G4 input stage ground nodes were connected with separate traces directly to the TPA32xx amplifier analog ground reference, G1. With this star ground connection scheme, G1 G2 G3 and G4 are well coupled and share the same ground potential. Therefore, no noise voltage can be developed between the input stage grounds and the TPA32xx analog ground. Figure 3 shows this connection scheme.

Figure 3. SE to Diff Input Stage Star Ground

TPA32xx Ground Pin Reference

For reference, the pinout of the analog and power ground pins on the TPA32xx devices are listed below.

TPA32xx Class-D Amplifier Ground Pins
AmplifierAnalog Ground PinsPower Ground Pins
TPA324410, 1125, 26, 33, 34, 41, 42
TPA324512, 1325, 26, 33, 34, 41, 42
TPA325010, 1125, 26, 33, 34, 41, 42
TPA325112, 1325, 26, 33, 34, 41, 42
TPA325512, 1325, 26, 33, 34, 41, 42

Componenti chiave

Numero di parte Descrizione
TPA3200D1DCPR
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR 20W D 44TSSOP RFQ
TPA3200D1DCPG4
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR 20W D 44TSSOP RFQ
TPA3200D1DCP
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR 20W D 44TSSOP RFQ
TPA3250D2DDW
Texas Instruments
Lineari - Amplificatori audio, IC POWER AMP CLASS D 44HTSSOP RFQ
TPA3244DDW
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO CLASS D 44HTSSOP RFQ
TPA3251D2DDVR
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR 44HTSSOP RFQ
TPA321DG4
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR .7W MONO 8SOIC RFQ
TPA321DGNRG4
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR .7W MONO 8MSOP RFQ
TPA321DGNR
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR .7W MONO 8MSOP RFQ
TPA321DGN
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR .7W MONO 8MSOP RFQ
TPA3255DDV
Texas Instruments
Lineari - Amplificatori audio, IC AUDIO AMP CLASS D 44HTSSOP RFQ
TPA3245DDV
Texas Instruments
Lineari - Amplificatori audio, IC AUDIO AMP CLASS D 44HTSSOP RFQ
TPA3255DDVR
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO CLASS D 44HTSSOP RFQ
TPA3250D2DDWR
Texas Instruments
Lineari - Amplificatori audio, IC POWER AMP CLASS D 44HTSSOP RFQ
TPA3245DDVR
Texas Instruments
Lineari - Amplificatori audio, IC AUDIO AMP CLASS D 44HTSSOP RFQ
TPA3244DDWR
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO CLASS D 44-HTSSOP RFQ
TPA321DR
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR .7W MONO 8SOIC RFQ
TPA321D
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR .7W MONO 8SOIC RFQ
TPA3251D2DDV
Texas Instruments
Lineari - Amplificatori audio, IC AMP AUDIO PWR 44HTSSOP RFQ

Related Articles

  • How to maximize the efficiency of SiC traction inverter by real-time variable grid drive strength?

    Traction inverters are the main battery drain components in electric vehicles (EVs), with power levels up to 150kW or higher. The efficiency and performance of traction inverter directly affect the driving range of electric vehicle after a single charge. Therefore, in order to build the next generation of traction inverter systems, silicon carbide (SiC) field effect transistor (FET) is widely used in the industry to achieve higher reliability, efficiency and power density.

  • Do you know the 8 application circuits of operational amplifiers?

    Do you know the 8 application circuits of operational amplifiers?

  • How do you configure an op-amp in a typical gain control circuit?

    This technical presentation requires an understanding of how to configure an operational amplifier in a typical gain control circuit. The applications of linear and nonlinear digital potentiometers are discussed. This article gives an overview of the basic techniques required to convert audio and other potentiometer/op amp applications from conventional mechanical potentiometers to solid state potentiometers

  • Simple way to limit current using integrated MOSFeTs

    The current in an electronic circuit usually has to be limited. In USB ports, for example, excessive current must be prevented to provide reliable protection for the circuit. Also in the power bank, the battery must be prevented from discharging. Too high discharge current results in too large voltage drop of the battery and insufficient supply voltage of downstream devices

  • Three excellent ways to reduce audible noise in motion control applications

    Using advanced real-time control technologies such as motor control circuits with higher power density, higher integration and more efficient systems, better acoustic performance of the system can be achieved

  • How to control brushless DC motor?

    Brushless direct current (BLDC) motors have been widely used in household appliances, industrial equipment and automobiles. While brushless DC motors offer a more reliable and maintainable alternative to traditional brushless motors, they require more sophisticated electronics to drive them

  • How to achieve precise motion control in industrial actuators

    How to achieve precise motion control in industrial actuators

  • Summary of PCB design strategy for GaN drivers

    The NCP51820 is a 650 V, high-speed, half-bridge driver capable of driving gallium nitride (" GaN ") power switches at dV/dt rates up to 200 V/ns. The full performance advantages of high voltage, high frequency and fast dV/dt edge rate switches can only be realized if the printed circuit board (PCB) can be properly designed to support this power switch. This paper will briefly introduce NCP51820 and the key points of PCB design of high performance GaN half bridge grid driver circuit using NCP51820